Your cart is empty.
Your cart is empty.Product Description
Product parameters
- Type: Coaxial cable, Male UHF straight PL-259 to Male UHF elbow Pl259
- Impedance: 50 Ohm
- RF Cable Type: RG58
- Cable Length: 3 Feet
- Connector Type:
- Connector A: UHF Plug straight, Male pin/pl259
- Connector B: UHF Plug elbow, Male pin/pl259
Used for Antennas, Antenna Analyzer,dummy load, Radio Scanner, Ham Radio Transceiver,SWR METER,CB Radio Handheld & Amateur Radio Equipment.
- Prevent damage to your radio's UHF antenna connection due to having to change antennas for base, mobile, or to a different style than stock antenna use. Adapter will take all the wear and tear; instead of the chassis connector being subjected to wear or coming loose. You can now quickly and safely change the more popular and wider selection of available UHF antennas, and help to protect your radio from damage, all at a low cost.
- Adapter allows you to: 1. Quickly change antennas to base, mobile or different style use.
2. Use the more popular and wider selection available of UHF antennas.
3. Prevent chassis connector wear or from coming loose due to antenna changes.
Dietmar
Reviewed in Germany on January 20, 2025
Brauchte auf die schnelle ein paar flexble, fertig konfektionierte Anschlusskabel mit PL Steckern.Sie erfüllen ihren Zweck und wurden von der Firma gut konfektioniert.
Brian M.
Reviewed in the United States on May 20, 2024
Got to have one if you want to attach your screen meter
KAREN KAY GILL
Reviewed in the United Kingdom on December 23, 2024
Good RG58 Patch cable.
K. A.
Reviewed in the United States on December 1, 2024
I have a Xiegu X6200 that has a BNC connector, and it kind of sticks out of the side of the radio, so it puts a bit of strain on the antenna coax. To combat that, I bought two of these sets of right-angle jumpers - the 1ft and 3ft. 1ft is the perfect length for attaching to a SWR meter or other short run for testing (such as a VNA). The 3ft length is used when I need to connect to the Xiegu XPA125B linear amp/tuner, and leaves me enough slack that nothing is being pulled unnecessarily.I think the next batch that I buy will be a 90 degree connector on both ends, that way all the cables lay flat and out of the way, and can be routed easily. I had no concerns with the quality of the cable, or the connectors. At this price point, I doubt these are full copper core, but are more likely CCA or very thinly-coated aluminum. In either case, they do the job well enough!
James Docheff
Reviewed in Canada on January 16, 2024
Jumpers arrived promptly looking good. Continuity tested perfectly. And that's where it ends! Put them in line. Started running them to check swr , power levels, set inductance, capacitance on tuner. By the time I had done that swr was shot!!! Went from a cruddy 1-1.7 to a horrible 1- 3+++. Time to shut down!! These things are for looking at. Not for using. I will NOT buy any other products from this super supplier.You have been warned. These things are garbage. They are NOT for hf radio use. Maybe home stereo or something. Not for cb/ ham.
Azak
Reviewed in Canada on June 3, 2023
One end wont tighten down and seat fully, thats 2 out of 4 cables i ordered that are junk and a waste of my time
EdM
Reviewed in the United States on February 25, 2023
I selected this jumper because I needed to connect a coax feedline in a very tight spot. The right angle connector on this jumper appeared to be the smallest of the several I looked at. When I got it, it did fit in my tight spot and worked for me. Durability and quality of construction appears to be good.
Recommended Products