Your cart is empty.
Your cart is empty.Amazon.ca Product Description
The BOSCH rebar cutter has the highest quality in the market at a lower price compared to other competitors.
From the Manufacturer
The BOSCH rebar cutter has the highest quality in the market at a lower price compared to other competitors.
Dickster
Reviewed in the United States on March 3, 2025
I hit some rebar with a regular cement bit and couldn’t get though it. I ordered this bit and it went right through.Don’t force it, just light pressure and it will do its job.
ken langton
Reviewed in the United States on February 2, 2025
Good value for the money
Daniel B.
Reviewed in the United States on January 21, 2025
I drilled down with a hammer drill and bit until I hit the rear, then switched to the rebar bit and regular drill mode and the cutter is still sharp and ready for the next hole.
RGD
Reviewed in the United States on September 18, 2024
When installing anchor bolts in reinforced concrete, I was unlucky to strike a half inch rebar. I realized that there are very few good options to remedy this problem: you either relocate whatever you are securing, which wasn't an option for me or buy one of these rebar cutters. The cutter went through the rebar in three locations and saved the day. I recommend these drill bits, which can save the day. I only drilled three holes with the bit but saw only minor damage to the bit. Great product!
R. Saint Eeves
Reviewed in Canada on June 30, 2023
Bad luck that under a line of holes for some concrete anchors to attached bases for the posts for my gazebo, was rebar the entire length. Took a while but eventually using this bit I cut through the rebar at 8 different hole locations. It was my only hope and this tool came through for me.
Miroslav
Reviewed in Canada on November 4, 2022
Great price
Wasabi
Reviewed in Canada on January 24, 2022
Make sure to keep drill cutter head cooled, cutting head gets very hot very quickly, I keep a small container of water close by to cool bit, it doesn't cut as quickly if you leave your drill at drilling mode only, I use it with drill and hammer mode switched on,
D. Brooks
Reviewed in Canada on April 15, 2022
I tried to reorder a RCSS2086 rebar cutter that I had purchased in September 2021. I was so happy with the result I wanted another one. However, when I ordered this this time, I failed to notice that this is not a cutter, but a carbide drill bit. It was a RCSS2086 1/2-Inch by 18-Inch, that I wanted, but this RC2084 drill was mixed in with the plug cutters. NOT HAPPY. If you want to cut rebar DO NOT BUY THIS DRILL BIT. It does not cut, it makes the rebar nice and shiny. Since it is an SDS shank, do not use hammer function either.
Emile
Reviewed in Canada on May 18, 2021
Great
Brad
Reviewed in the United States on August 4, 2019
I returned the bit because it would not cut through rebar as advertised. Instead it wallowed out the hole where and additional shim was necessary to get the anchor to hold. Not only that, the full amount of the refund was not issued. I am requesting the full amount. Not only did it waste my time both by me having to repair the hole but also by having to pack it back up and ship it back.
Peter C
Reviewed in Canada on August 31, 2018
Good basic hammer drill for price. Used to drill concrete including 12" rebar cutter purchased, which worked well.
Customer
Reviewed in Canada on July 11, 2018
1-1/8”Used under water in overhead positionWith a a pneumatic Spitzna dill. Worked well.
Chris
Reviewed in Canada on July 26, 2017
It did the job, but it took nearly an hour to remove 2 pieces of rebar. Constant application of cutting fluid and medium pressure to prevent the edges from getting dull.
Recommended Products
CA $121.86
CA $ 57 .99 CA $57.99