Shopping Cart

Your cart is empty.

Your cart is empty.

915MHz ESP32 LoRa V3 Development Board SX1262 0.96 Inch OLED Display WiFi+BLE Lora Kit with LoRa Antenna for Arduino IOT Smart Home (2Sets)

Free shipping on orders over CA $49.99

CA $71.99

CA $ 27 .99 CA $27.99

In Stock

About this item

  • WiFi LoRa 32 is a classic IoT dev-board. The newly launched V3 version retains Wi-Fi, BLE, LoRa, OLED display, and other functions
  • V3 version has better impedance matching of RF circuits
  • MCU: ESP32-S3, LoRa Chip: SX1262, USB Socket: Type-C
  • When you use esp32 oled lora, you need to use 2pcs together. One is used for receiving and another for sending
  • It is the best option for smart cities, farms, homes, industrial control, house security, wireless meter reading, and IoT developers
  • What you will get: 2 X ESP32 Lora V3 OLED development board + 2 X 915MHz U.FL IPEX to SMA Connector Antenna + 2 X JST 1.25mm-2P Connector + 2.54 pin (no welding)


915MHz ESP32 LoRa 32 V3 Development Board
Features:
- Microprocessor: ESP32-S3FN8 (Xtensa (R) 32-bit LX7 dual-core processor, five-stage pipeline rack Structure, frequency up to 240 MHz).
- SX1262 LoRa node chip.
- Type-C USB interface with a complete voltage regulator, ESD protection, short circuit protection, RF shielding, and other protection measures.
- Onboard SH1.25-2 battery interface, integrated lithium battery management system (charge and discharge management, overcharge protection, battery power detection, USB / battery power automatic switching).
- Integrated WiFi, LoRa, Bluetooth three network connections, onboard Wi-Fi, Bluetooth dedicated 2.4GHz metal spring antenna, reserved IPEX (U.FL) interface for LoRa use.
- Onboard 0.96-inch 128x64 dot matrix OLED display can be used to display debugging information, battery power, and other information.
- Integrated CP2102 USB to serial port chip, convenient for program downloading, and debugging information printing.
- Support the Arduino development environment.
- This is a standard LoRaWAN protocol that can communicate with any LoRa gateway running the LoRaWAN protocol. To make this code run, a unique license is needed.
- With good RF circuit design and low-power design.
U.FL IPEX to SMA Connector Antenna 915MHz for Lora Board Lora32u4 II Wifi Lora32 10cm
Description:
Connector type: ipex
Band definition: 915MHz
Standing wave ratio: Gain: 2dBi
Maximum power: 10W
Input impedance: 50Ω
Package Includes:
2 X ESP32 Lora V3 OLED development board
2 X 915MHz U.FL IPEX to SMA Connector Antenna
2 X JST 1.25mm-2P Connector
2.54 pin (no welding)


Donald
Reviewed in Australia on March 1, 2025
I'm sure this is a terrific product but it was denied entry and returned to the shipper by Australian Customs.
PETRA
Reviewed in the United States on August 30, 2024
Great LoRa radios. I have enjoyed dealing with DIY malls in general. Great price.
RFGuy
Reviewed in the United States on August 6, 2023
The media could not be loaded.
S.A.
Reviewed in the United States on December 13, 2023
Great even without using the lora on this device, as an ESP32. Nice built in features, especially the display and charge circuit. Great option to start off with lora. You can easily set up a long range (w/ line of sight) communication (no license required for point to point with just your two devices).
Recommended Products

CA $7.01

CA $ 3 .99 CA $3.99

4.5
Select Option

CA $183.13

CA $ 75 .99 CA $75.99

4.3
Select Option