Your cart is empty.
Your cart is empty. A QUALITY SPIGOT FOR YOUR RAIN BARREL. Make use of the water collected from your rain barrel easily. This spigot is designed to provide a strong water flow by relying on pressure from the water in your rain barrel. The 3/4" spigot is threaded for easy use with a hose- no need to haul buckets or watering cans.
NO LEAKS. The attached washer and silicone tape provide a perfect waterproof seal, and the bulkhead fitting and spigot are reverse-threaded, and self tighten- which ensures the spigot will not accidentally loosen from use, and will hold a tight seal over multiple seasons.
INSTALLATION SO QUICK, YOU'LL BARELY HAVE TIME TO GET YOUR DRILL OUT. The bulkhead fitting and spigot are reverse-threaded, and are tightened from the outside of the barrel- no need to fiddle inside with a wrench. Simply drill a hole, and thread the attached wire down through the hole then slide the bulkhead fitting down the wire as a guide- works well for barrels with and without open top design. The product also comes with a detailed, illustrated guide.
HEAVY-DUTY, DURABLE CONSTRUCTION. From using a brass ball valve and body and aluminum handle (with orange paint spray), this spigot is built for longevity. The spigot also contains less than 0.25% lead, compliant with the EPA's Lead Free requirement. Visit epa.gov for more info.
COMPLETE KIT AT A FAIR PRICE. Instead of purchasing separate washers and fittings, save yourself time and money by purchasing this full kit at once. This kit contains: 3/4" spigot with quarter turn valve, 3/4 inch bulkhead fitting (with washer), roll of teflon tape, wire, installation guide.
REQUIRED: Drill, a 1-1/4 inch saw bit, adjustable or 1 inch wrench.
Joe Kelly
Reviewed in the United States on April 1, 2025
Super easy to install. All the parts go right together and instructions lay it all out for you to do. Rain barrel works great and hose bib hooks right up a normal garden hose without leaking.
GJR
Reviewed in the United States on July 22, 2024
The bulkhead and faucet are well made and sturdy. Instructions are clear and include important details like “ wrap Teflon tape five times”. The standard three left mine leaking. Five layers was perfect. Having used other bulkheads, I want to assure you, one silicone washer on the inside of the barrel is the best design available. You simply clean the surfaces, tighten the outer nut and it’s done. Silicone or rubber on both sides causes problems. One must very carefully tighten, tight, but not too tight, and adding a hose can easily change the ideal tightness. This one has it right in every way. I have used it daily for two months, and I am confident this faucet will last. The valve is still smooth. Everything looks strong, without leaks. I have seen many other designs and especially plastic that I know will not last, and product reviews seem to agree with me. A second valve was installed today on a second barrel. It was so much easier than the first. I’m very happy with this product.
Momma
Reviewed in Canada on June 13, 2024
Easy install if you have the right drill head. Followed instructions and was not hard at all.
Phoenix
Reviewed in Canada on May 26, 2024
I bought these for our rain barrels, install is easy and comes with all that you would need.I wish the cost was a little lower, but like things today, you get what you pay for and I must say their are well built and very solid/with great machine work.
Hung Lo
Reviewed in the United States on July 3, 2023
I purchased this kit to set up a buffer tank for a pressure washer. As supplied, the only things I needed to complete the installation were a hole saw and a weight to aid in accessing the rope.I positioned the mount hole a little lower than YouTube video recommendations, but high enough to clear the bulkhead fitting flange, cleaned around the hole to reduce leak paths, installed the fitting and nut, and then torqued down everything snuggly.After taping and installing the spigot, I filled the barrel and checked for leaks. Finding none, I measured flow rate next since this will need to supply at least 4.4 GPM for the washer pump. With about 15 gallons in a 55 gallon barrel, I noted a little over 4 gallons per minute flow. Under power, with the barrel supplying water to the pump, this setup easily met the pump's input needs.The brass components all appear to be of good build quality - everything fit as it should and I'm happy with kit performance.
J. Derryberry
Reviewed in the United States on May 22, 2023
My first rainbarrel had a small tube molded into the bottom that a hose was pushed onto and held in place with a clamp. Well, that small tube was sloped to allow the hose to be pushed on easier and therefore it was always getting popped off. Finally decided this year was the year to close off that tube and put in a better spigot. This one was extremely easy to install, and I had a small opening so used the string that came with it...what a simple yet highly efficient way to get the first parts on...I was very impressed with the design and especially happy that the handle is also metal. I did the installation in just a few minutes, and put a plug and a heavy coating of silicone glue over the old tube. This week is scheduled for rain, and I am really happy with the quality of this spigot...it is going to make the rainbarrel much much better to use and a welcomed bit of confidence that the hose isn't going to fall off!
Danmop
Reviewed in the United States on June 6, 2022
Great product - precision craftsmanship. Wanted to create a rain barrel and plug a hose bib near bottom of the barrel. Originally had PVC plugs and bib but threads kept stripping out, leaked like a sieve. No problem with this Brass spigot! Easy bolt-on application, unit comes shipped with everything you need in a fully protected box so almost no chance of any damage during shipping (should have took pic of the box before I installed the valve - better late then never). Cant say the same thing for similar type of items I've gotten from other vendors. These guys show their care for their products and their customers!My only comment for improvement about this product - be helpful if the washer and flange size was bit bigger for this kind of application. Existing washer barely covered the hole drilled in the barrel, which was not easy getting a "precise" size opening. The square black thing you see inside the barrel was my own oversize washer I cut from a 1/8 thick rubber strip. In spite of this minor issue, I still think everything worth 5 stars - Overall an excellent product.In any case, my rain barrel project is a success - No stripped threads, no Leaks! I'm a happy camper...
Recommended Products
