Your cart is empty.
Your cart is empty. Compatibile with:RC Cars Airplanes Helicopters Boats Robot,etc.
Features:
Material:Aluminum (sturdy and durable, dissipates heat quickly)
It has pre made holes to support 18 different sizes,list of the holes as follows:
XT60 Male
XT60 Female
T Connector
XT90 Male
XT90 Female
Mini-T;
For bullet connectors you are offered the following sizes: 10.4mm, 8.3mm, 7.8mm, 6.9mm, 5.8mm, 5.3mm, 5.0mm, 4.6mm, 4.3mm, 3.2mm, 2.7mm, 2.4mm
Size:60x110x15mm (LxWxH) small enough to take with you when you go to the flying field
Thermal Insulating Layer: Black thermal insulating layer surrounded by the holes, which can effectively prevent heat propagation.
Packing List:
1 x Soldering jig -Red
Note:Check your specific model's manual for compatibility.
Lukas
Reviewed in Canada on February 23, 2024
Its a well designed little soldering jig for finicky little connectors.
Wayne joudrey
Reviewed in Canada on June 24, 2023
Works great and I wish I'd have had one years ago
kevin l. farmer
Reviewed in the United States on November 2, 2023
Much easier than "helping hands" to hold connectors while soldering.
Harley Davis
Reviewed in the United States on January 23, 2022
Well made, easy to use. Well done.
Luis Peral
Reviewed in Canada on July 19, 2021
It is just a terminal holder jig, nothing special to mention.
Frank
Reviewed in Canada on June 15, 2021
Great tool, holds connectors steady while soldering.
Customer
Reviewed in the United States on March 5, 2021
This tool works perfectly! Holds many different types of connectors so you don’t have to. Allows much easier solder jobs.
John G Davis
Reviewed in the United States on August 6, 2020
Great little jig. I had been really struggling with getting successful soldered joints on XT90 connectors. The XT90 and XT60 had highlighted my poor soldering skills. I was using my Panavise to hold the connectors, but was overheating the connector pins and even having the pins move or completely drop out of the connector. This little jig has help tremendously as it holds the connector and appears to distribute the heat. I still had the problem of the jig sliding around on my workbench, so I made a extra jig to hold the ShareGoo jig. It's just a couple of pieces of 3/4" plywood, with a couple of dowels, but it allows me to clamp my jig to the workbench and the soldering jig stays rock solid. My soldering skills probably still suck, but I am now getting perfect soldered joints every time. I hope the photos help.
Customer
Reviewed in Canada on August 20, 2020
the unit is ok but not strong
Darren c
Reviewed in Canada on September 15, 2019
Perfect for holding the sockets for soldering
YYCRCFabricationz
Reviewed in Canada on August 12, 2019
A great jig, simple & easy to use & well made!
RicM
Reviewed in the United States on March 15, 2019
Update:I contacted the seller and received very very good customer service. They responded quickly and were very fast to replace the jig with a new one. The XT slots in the replacement are resized and fit and hold the connector perfectly. I am very happy with the purchase and the customer service.Original:It holds the half with the female connectors fine, but it's too big for the half with the male connectors.I could, I suppose, add some tape or something - but if I did that, I suppose I could also just tape the connector to something instead of using the jig.I've contacted the seller to see if there's an updated version or something. Otherwise it'll go back.
Darrell dube
Reviewed in Canada on December 4, 2018
Works really well
Recommended Products
